Hardware

Aluminum Tiller Extension from Harken. The rigid anodized body of this tiller extension transmits subtle boat and rudder movements, allowing you to steer by the feel of the helm. The elegantly simple and lightweight design has no unnecessary...

Aluminum Tiller Extension from Harken. The rigid anodized body of this tiller extension transmits subtle boat and rudder movements, allowing you to steer by the feel of the helm. The elegantly simple and lightweight design has no unnecessary...

Aluminum Tiller Extension from Harken. The rigid anodized body of this tiller extension transmits subtle boat and rudder movements, allowing you to steer by the feel of the helm. The elegantly simple and lightweight design has no unnecessary...

Aluminum Tiller Extension from Harken. The rigid anodized body of this tiller extension transmits subtle boat and rudder movements, allowing you to steer by the feel of the helm. The elegantly simple and lightweight design has no unnecessary...

Aluminum Tiller Extension from Harken. The rigid anodized body of this tiller extension transmits subtle boat and rudder movements, allowing you to steer by the feel of the helm. The elegantly simple and lightweight design has no unnecessary...

These robust low-friction ball bearing handles match a wide range of cranking needs for both racers and cruisers. Ball bearing grip that efficiently transmits power into the winch. All handles fit international standard winch sockets.

Track is extruded from high-grade 6061-T6 aluminum and hardcoat-anodized for a hard, long-lasting surface. 3807 track mounts to mast using a unique slug system that allows mast-up installation. ONE DESIGN APPLICATIONS This fitting is commonly used and/or...

Harken Small Boat furling systems allow the trailerable cruising or dinghy sailor to set and furl the jib from the cockpit. An optional hoistable ball bearing halyard swivel can be installed on your headstay so you can raise or lower the sail without...

This is a standard bow shackle used commonly on the 420, FJ & V15 and as a mast bail on 3:1 purchase 420 vangs. It is an excellent shackle for all-around use with screw pin included. HAR 2110 1/4 inch / 6mm diameter screw pin for easy...

Use the 237 and 339 where there is little deflection in the line such as when routing a spinnaker pole foreguy aft along the cabin house. Use with Harken 241 cam base. A (mm)32 mm A (in)1 1/4 in B (mm)38 mm B (in)1 1/2 in Fasteners (mm)5 RH...

Stamped shackles are used on most small boat blocks and are appropriate for low loads. This shackle has a 6 mm / 1/4 inch pin with a ring for easy attachment. For higher loads, select forged and high-resistance shackles instead. Shackle pin: (mm)6...

The Harken Swivel Cam Cleat is a simple swivel base for main and jib sheets on small sailboats. Includes a swivel base, bullseye fairlead, and standard Harken cam cleat. The base rotates 360 degrees making it easy to cleat and un-cleat from any angle...

Wire fairleads maintain a low profile while holding the line close to the cleat.. Height (mm)32 mm Height (in)1 1/4 in Length (mm)65 mm Length (in)2 9/16 in Width (mm)32 mm Width (in)1 1/4 in Weight (g)14 g Weight (oz)0.5 oz Fastener spacing (mm)38 mm...

Harken cam cleats utilize a system of multiple rows of ballbearings allowing the line to be cleated by snapping down rather than drawing through. The cams are design to provide maximum holding power without destroying the line. This includes smooth...

Large stainless eyestrap from Harken. ONE DESIGN APPLICATIONS This fitting is commonly used and/or recommended for the following one design sailboat applications: J/22 Traveler Block Eyestrap (x2)    

The horn cleat is perfect for tying off halyards securely. Used on a variety of small sailboats, including the Sunfish for securing the main halyard. 3-3/4 inch length. Black anodized aluminum. Commonly found on Sunfish deck for main halyard cleating.