1/4 inch x 1 inch stainless steel clevis pin with zinc finish from Ronstan. Features a 1 inch grip length (distance between cap and pin hole) and 1-3/16 total pin length. Pin Diameter is 1/4 inches Pin Grip Length is 1 inch Sold individually Made by...

The Grabrail Captive Nuts insert into existing holes on the sides of the Laser or ILCA sailboat cockpit and allow for grabrails to be screwed in. Also used on boats like the Vanguard 15 that use a similar grabrail. 10 Pack Black Plastic Uses...

Expand the rigging capabilities of inflatables, stand up paddleboards or coolers (without drilling). The i-Series Base allows the addition of useful StarPort attachments. The 6x4-1/2 inch base is easily applied to any flat surface with the included 3M...

Forestay wire for Club 420 sailboats from Zim and Laser Performance. This stainless steel forestay supports the mast from the bow. 3/32 inch diameter Approximately 14 foot 6 inches long Fits Club 420 sailboats from Zim and LaserPerformance Zim Part...

Batten Cap for Hobie catamaran jib sails. Made of a high strength Delrin for great durability. Solid individually. 4:1 mechanical advantage allows finer adjustment than does Trentec 2:1 caps. Release the batten tension whenever you store your sails...

5/18-18 x 2 inch stainless screw from Hobie Cat. RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All Hobie Cat Parts

This safety shackle is made from stainless steel and can be easily released with one hand. Stainless steel construction Easy one handed use

This is the C420 centerboard gasket material for use on newer C420s with recessed gaskets. Slightly wider than original material. One piece only. Durable mylar plastic material Single gasket piece only 1.5" wide Zim Part # 20358 / Laser Performance Part...

The Tasar Mast Step Plate mounts to the deck of the Tasar and allows the mast to rotate. This new design step fits most older screw patterns and fits all mast step plugs. The pin is machined from solid stainless steel to prevent pin failure. Machined...

This Opti boom end plug fits the aft end of the boom and accepts the outhaul line. The cap fits any 32mm standard opti boom. Fits any Opti boom with an interior diameter of 32mm Seals the boom from water intrusion

Replacement seat pad for the Hobie Wave catamaran. Sold individually, these pads have an adhesive backing for easy application to your boat. Soft seat pad for the Hobie Wave, identical to pads installed on new boats Includes adhesive backing on...

Brace Ball for Hobie Mirage AKA brace arm. HCC Part # 79525001 Brace Ball Sold Individually   RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All Hobie Cat Parts

The Sunfish Bow Bumper is a simple accessory to keep this vulnerable part of the boat protected from common scratches and dings. It is molded with a high-grade rubber compound so you can be sure it is tough and long lasting. It is a two-piece set,...

C420 hiking strap, black webbing with a pad underneath for comfort when hiking hard. This strap has center webbing loops to tie on to the traveller bar. Sold as single straps, add 2 to cart for a pair. Full length strap - crew and skipper Fully padded...

Harken cam cleats utilize a system of multiple rows of ballbearings allowing the line to be cleated by snapping down rather than drawing through. The cams are design to provide maximum holding power without destroying the line. This includes smooth...

Spacer of the traveler car assembly of Hobie 14, Hobie 16 and Getaway catamarans. Application: component of the main traveler car assembly Fits Hobie 14, Hobie 16 and Getaway catamarans   RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat...