Stainless steel mast tang for Hobie 16, Hobie 17, and Hobie 18 catamarans. RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All Hobie Cat Parts

Cradles distribute the boat load over 400 sq. in. of the hull to assure there are no excess stresses while carrying. Recommended for Wildcat, H18, H20, and Hobie 16. Can be used on Hobie Getaway or Hobie Wave, but long term storage of rotomolded boats on...

Replacement back frame assembly for Hobie Vantage kayak seat.   RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All Hobie Cat Parts

Replacement tiller arm for the Hobie 16. Made from aluminum. RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All Hobie Cat Parts

This is a forestay for those Hobie 16s using the Aussie jib halyard system. This replaces the forestay wire found in the Aussie upgrade kit, or can be used to upgrade your jib halyard system. Use with Hobie 16 Aussie Jib Halyard system. Measured at 225...

Replace the rudder cam and flared pin with this kit that includes a pair of cams and a pair of binding post screws. Fits the Hobie 17, Hobie 18, and Hobie 20.   RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All...

Hobie Mirage Drive 180 V2 replacement fin. Hobie Part Number 81500 Previous Hobie Part Number 81500002   RESOURCES & SUPPORT Hobie Cat Parts Locators Hobie Cat Rigging Guides Shop All Hobie Cat Parts

The bailer assembly is mounted to the hull of the ISCA to provide a way to drain water from the cockpit. The complete assembly has a housing that is mounted to the hull with a threaded cap that screws into the housing from the cockpit with a rubber plug...

ISCA Bailer Ball & Seal 5 pack. A handy spare item to have on hand for any ISCA / Sunfish sailor.  Zim Sailing Part # 41032 Previous LP Part # 91031 This is an official International Sunfish Class Association™ (ISCA®) class...

Race spec line kit for the ISCA sailboat, found on all Zim Sailing ISCA - Race boats. Includes all the lines you need to upgrade your boat! Race Line KitEvo X mainsheet (2:1) Dyneema Halyard Dyneema Outhaul Dyneema Cunningham 2x Stainless thimbles...

Rudder Cheek for the ISCA sailboat. This is an updated design found exclusively at Zim Sailing, offering stronger, more durable plastic for long life. Includes pintle pin and spring.  Rudder Cheek Includes Pintle Pin & Spring Zim Sailing...

Replacement Pintle Pin and Spring Kit for the ISCA sailboat rudder assembly. This kit includes the pintle pin, compression spring, washer, and cotter pin.  Complete Pintle Pin and Spring Kit Includes Pintle, Spring, Washer, and Cotter Pin Zim...

The bailer assembly is mounted to the hull of the ISCA to provide a way to drain water from the cockpit. The complete assembly has a housing that is mounted to the hull with a threaded cap that screws into the housing from the cockpit with a rubber plug...

ISCA cockpit trim clip.    This is an official International Sunfish Class Association™ (ISCA®) class approved fitting. Zim Sailing is the exclusive manufacturer and distributor of the ISCA® Boat and Equipment. Boats and...

Replacement boom end cap for the ISCA sailboat. This 'Double Eye' version is used at the aft end of the lower boom to accommodate the outhaul rigging. Compatible with older Sunfish® and lateen rigged sailboats. End Cap w/ Double...

Stainless steel pintle pin for the ISCA sailboat. This pin is used to connect the ISCA rudder assembly to the gudgeon on the transom of the boat. This is the pin only (does not include washer, spring, or cotter pin). ISCA Pintle Pin Stainless...